您的位置:优秀啊电子开料锯操作说明书电子开料锯,FMEAcase1开料,开料软件破解版下载,板材开料软件破解下载 → 正文

电子开料锯,FMEAcase1开料,开料软件破解版下载,板材开料软件破解下载

Process FMEA 流 程 FMEA 表 FMEA No.: Item 项目: Desmear&PTH/化學沉銅 Process Responsibility流程责任: QA, PE, PROD,ES, QC Page No./页数: Prepared by编制者: ...

这样当一 Process FMEA 流 程 FMEA 表 FMEA No: B5-CUT-B 1 of 1 Page No./页数: Item 项目: Cutting/開料 Process Responsibility 流程责任: PE、QC、PROD、ES Prepared by编制者:

Year/Vehicle mode年型/车型:

N/A Key Date 关键日期:

04/10/2001 Reviewed by审核:

FMEA /Date日期:(编制)2001-04-07(修订)2001-09-19 Potential Effects of Failure 失误的潜在影响 1.1后工序生产困难 induce difficult to next process C l a s s Potential Causes of failure 失误的可能成因 1.1.1 员工操作失誤 wrong operation 1.1.2 量具不准确 bad measurement Current Process Controls 当前的流程控制 首板OK方可生产 Control by checking sample QA定期校准量具 O c c u r 1 D e t e c 1 FMEA core Team/中心小组: Process Function &Requirements 流程功能与要求 开料 Potential Failure Mode 潜在的失误形式 1. 尺寸超差 size out of requirement Recommended Actions R P N 4 S e v 4 Responsibility&Target Completion time 责任和完成目标 Action Result 行动结果 Actions Records 行动记录 S e v O c c 建议措施 将来料切割成大小、 板厚度均符合MI要求 的单元板 CUT cut material to fit requirement of MI 2.经纬向错误 wrong wrap and fill direction 2.1层压后板收缩不一致,造 成板翘曲 warpage, poor dimensional stability 7 1 2 8 QA calibrate regularly SC 2.1.1 员工對經緯方向 按照MI操作 辨別失誤 Operate according not distinguish to MI latitude&longitude of 领班检查 lamination operator leader audit 2.1.2 余料标识错误 两个员工一起标识余 料 wrong mark of leftover monitored by another material operator when one marks the rest of materials 1 5 35 2 2 28 N/A 無 3. 开错料 cut wrong material 4. 擦花、凹痕 scratch、dent 3.1板厚超标,客户拒收 board thickness out of the requirement of customer 4.1开路 open 8 SC 3.1.1员工操作不当 bad operation 开料后QC检查 QC check after cutting 開料前检查 check material before cutting 生产前日常保养 daily maintain before prodution 依照MI及WI操作 Operate according to MI&WI 依照MI及WI操作 2 1 16 8 4.1.1 來料缺陷 Non-conforming incoming materials 4.1.2. 机台不清洁 bad cleaning of machine 5.1.1参数设置不当 poorl parameter set up in operating 6.1.1参数设置不当 2 2 32 2 2 32 5.烘板温度过高时间过 5.1板面氧化,板变形 长 bake temp. is too high and laminate oxide and distort time is too long 6.1板内水份过高尺寸不稳定 6.烘板温度过低时间过短 6 1 2 12 6 1 2 12 bake temp. is too low and time is too short poor dimesion for too much moisture poorl parameter set up in operating Operate according to MI&WI Action Result 行动结果 D e t R P N

FMEAcase1开料 如要提出功能问题或意见建议,请 点击此处 进行反馈. FMEAcase1开料 暂无评价 | 0人阅读 | 0次下载 | 举报文档 你可能喜欢 今日推荐 78份文档 您的评论 *感谢支...

BoundaryDiagram Identifies and quantifies the strength of System Interactions Interface Matrix Identifies Noise and Control Factors and Error States P-Diagram FMEA with ...

团队 ? 主人 ? 设计师 ? 装修队监理 ? 水电工 ? 木工 ? 泥工 ? 油漆工 ? 供应商若干 3 of Version 20080325 Engineering Quality Department 装修DFMEA案例 FMEA Case in ...

推荐文章